Water Storage Tanks & Chemical Storage Tanks from Drayton Tank

Drayton Tank & Accessories was established in the 1990's to supply the whole of the UK with GRP water storage tanks of the highest quality. With a wide selection of products ranging from large industrial and commercial water storage tanks through to domestic water tanks, Drayton Tank have built up a reputation of the highest level offering outstanding products and exceptional customer service. Because of this we are now one of the largest storage tank suppliers in the UK. Whatever your requirement, be it for chemicals, water, waste and hot water, Drayton Tank & Accessories are the only company you need to call.

About Drayton Tank & Accessories

Located in both South Yorkshire and the Midlands, Drayton Tank and Accessories are perfectly situated to supply to the whole of the UK and offers water storage tanks that comply with British and European regulations and standards. Our tanks also meet the approval of the WRAS (Water Regulations Advisory Scheme) for the storage of drinking water. Also included in this is chemical storage and both hot and waste water storage requirements for both industrial applications and commercial applications.

Chemical and Water Storage Tanks

We offer a wide range of tanks from as small as 45 litres all the way through to 90,000 litres in our range of approved once piece tanks. These are designed to store a wide range of liquids and are available with and without insulation. All of these tanks must not be used unless installed on a fully flat, fully supported base.

One Piece GRP Tanks

Our one piece tanks can be used for a wide variety of applications and also located, with no access restrictions, outside. Our fiberglass tanks have no internal joists or support and internally the surface is smooth. Tanks can be produced to blend in with their location as they are available in a wide selection of external colours.

Manufactured pre-insulated or plain, our one piece tanks have no support internally, with just a smooth internal surface that is resistant to bacteria. External steel supports can be encapsulated into the tank's walls when required.

One Piece Tanks are available in three different resins:-

Key Features of our One Piece Tanks

• Free from joints or internal supports
• Internal surface that is both smooth and bacteria resistant
• Available with an Apexed roof option to deal with snow or rain
• Available insulated with HCFC free foam
• Better value in comparison to a sectional tank
• All tanks are manufactured to meet BS EN 13280:2001

Two Piece GRP Tanks

With no internal supports our two piece tanks and designed for projects that may have access issues (doorways etc). These tanks can be separated in to two individual pieces along their height, which allows for greater access through corridors and doorways and are easily put together once in the desired location. They offer the end user with an economical and cost effective alternative to your more common sectional panel tank.

Two Piece GRP Tanks from Drayton Tank & Accessories are designed to offer a cost effective, viable option where a sectional tank is too expensive and you have an access route which is restricted. Again, like our One Piece GRP Tanks, these Two Piece GRP Tanks have an internal surface that has no internal supports and has a smooth, bacteria resistant finish.

Main Features of our Two Piece Tanks

• No supports internally
• An interior resistant from Bacteria and with a smooth finish
• Apexed Roof option to deal with problems like snow and rain
• Tanks insulated with HCFC foam if required
• All the mobility of a sectional tank but much more cost effective
• Manufactured to comply with BS EN 13280:2001

GRP Sectional Tanks

If you require a tank that had a large capacity but access to the area is restricted then you may have to consider a sectional tank. Manufactured from GRP tank panels, these sectional tanks are easily brought to the location and can be assembled by our specialist team within your required area.

Drayton Tank & Accessories offer sectional tanks both pre-insulated and plain and can also be constructed from a combination of GRP panels that are sealed and bolted together on location and can be completely flanged internally with only a 50mm space required around the tank for assembly. All sectional tanks that we supply come with both inspection hatch and sectional hatch.

Features of our Sectional Tanks

• Suitable for locations with restricted access
• Tanks available with foam insulation which is HCFC free
• 1000 x 1000mm standard panel size, custom sizes available upon request
• With no restriction on length or width, height is a maximum of 3m
• Constructed and manufactured to BS EN 13280:2001